Shear screw and double wedge coupling sleeve and steel coupling sleeve with wedge are two examples of mechanical lap splices. Therefore, mechanical lap splices are considerably suitable for repairing structures because smaller concrete area need to be removed compared with lap splices. Therefore, if such condition is not guaranteed, then it is recommended to avoid its use.Ĭomparatively, mechanical lap splices are shorter than lap splices because of the use of coupling sleeves to connect reinforcement bars. This type of splice is suitable for the case where tension forces are present only. Upset bar and coupling sleeve with straight threadsįig.5: Cold Swaged Coupler with Taper Threaded Endįig.6: Coupler for Thread-Like Deformed Reinforcing Barsįig.7: Extruded Steel Coupler with Parallel Threaded Ends Mechanical Lap Splices or Tension Only Splices Threaded coupler with upsized bar threads, hot forged Threaded coupler with upsized bar threads, cold forged Threaded coupler with standard national coarse threads Grout-filled coupling sleeve with taper thread Grout-filled coupling sleeve with parallel thread at upset bar ends Size ranges of steel bar suitable to be splicedĬold-swaged coupler with taper-threaded endsĬoupler for thread-like deformed reinforcing barsĮxtruded steel coupler with parallel threaded endsįriction-welded bar coupler with parallel threadsįriction-welded coupler with taper-threaded ends Table-1: Tension and Compression Mechanical Splice Types, Their Designated Steel Number, Steel Bar Type and Applications Tension-compression mechanical splice type Number of tension and compression mechanical splices is shown from Figure-4 to Figure-7. Tension and compression mechanical splices types, designated bar sizes to be spliced by each splice type, the grade of the steel bar which is spliced using certain type of tension and compression mechanical splice, and installation condition of each mechanical splices are provided in Table-1. There are sizable numbers of commercially manufactured tension and compression mechanical splices. This type of mechanical splice can resist tension and compression stress. Tension and Compression Mechanical Splices for Rebars It should be known that the end of the rebars need to be saw cut in the case of strap type steel coupling sleeve, but no special end preparation is needed for steel filled coupling sleeve. 57 whereas the latter is suitable for splicing bar size ranges from No.22 to No.57.įig.2: Steel Filled Coupling Sleeve Spliceįig.3: Strap Type Steel Coupling Sleeve Splice The former can be used to splice rebar sizes ranges from No. Steel filled coupling sleeve and strap type steel coupling sleeve are the two most commonly used examples of end bearing splices. Therefore, if this condition cannot be guaranteed, then it is advised to avoid the use of compression only mechanical splices for reinforcement bars. The compressive stress is transferred by vertical bearing from one bar to another one.Ĭompression only mechanical splices can be used when tension stress is not occurred. Mechanical lap splices or tension only mechanical spliceįig.1: Mechanical Splices for Reinforcement Bars Compression Only Mechanical Splices or End Bearing SplicesĪs it may be noticed from its name, this type of splice can resist compression stress merely.Tension and compression mechanical splices.Compression only mechanical splices or end bearing splices.There are four major types of mechanical splices: Mechanical splices in reinforced concrete construction should meet the building code requirements for developing tension and compression as required These are designed based on codes of standard practice. It is an easy way, that avoids splicing or soldering, to connect each of the three color channels and one power channel of an RGB light bar to the controller that allows you assign color values and color-changing modes to the fixture.□ Reading time: 1 minuteMechanical rebar splices for rebars in concrete construction is an effective method of joining reinforcing bars. This connector is an essential accessory for getting the most out of our RGB LED light bars, as it provides an interface between the light fixture and the color controller. Each wire is connected to the corresponding jack on an RGB color controller, which is a necessary interface between our RGB light bars and a power source. The other end of the connector features four wires: one each of red, green, blue, and DC power. The female connector features and RGB light bar-style plug that connects to the male plug hard-wired on our TRUE FOCUS RGB LED light bars. These connectors are sold by the pair, which includes one male and one female cable. The RGB LED Light Bar Splice Cable is designed to make an easy connection between our TRUE FOCUS™ RGB LED Light Bars and an RGB color controller.
0 Comments
Leave a Reply. |
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |